400-101-5915 CN
400-101-5915 CN
Product
GHC window glass heating controller

GHC window glass heating controller / GHC型

Function : GHC type window glass heating controller is designed to prevent the ice, snow, frost and fog on the bridge window surface of the ship from affecting the sight of the pilot when the ship is in a low temperature environment. It can be used to manually/automatically control the heating of the glass window. The window glass heating controller is not only beautiful in appearance, simple in operation and reliable in performance, but also has the functions of adjustable heating temperature, real-time display of temperature, temperature inspection and over-temperature alarm, etc. It is an ideal product for window glass heating in ships.
Features :

The control panel adopts LED indicator and key operation, with beautiful appearance, clear indication and easy operation and maintenance

The control panel has local dimming function and CAN interface with remote unified dimming

Temperature display and setting: The window heating controller can display the real-time temperature of the window glass and set its heating temperature

Overtemperature automatic alarm: When the glass temperature exceeds the set alarm temperature value of more than 2 degrees (to prevent the influence of heater residual temperature), the buzzer will send intermittent alarm sound to remind the operator

Manual/automatic mode can be switched: In manual mode, when the window glass temperature is lower than the lower limit of the set heating temperature range, the window glass is heated for a single time. When the window glass reaches the upper limit of the set temperature range, it will automatically stop and no longer work. In the automatic mode, when the window glass temperature is lower than the lower limit of the set heating temperature range, the window glass will be heated automatically. When the window glass reaches the upper limit of the set temperature range, it will automatically stop to realize the cyclic heating of the window glass

Selection of inspection mode/fixed point mode: Inspection: the window heating controller circulates the "window glass number" and the corresponding "window glass temperature" in sequence; Fixed point: The window heating controller specifies the display of a single "window glass number" and the corresponding "window glass temperature"

Alarm function: When the glass temperature exceeds the set alarm temperature value, the window heating controller emits sound and light alarm

Model namedDetailed parametersPrinciple block diagramOperating instructionsAttachment configuration

工作电压

单相AC220V±10%50/60Hz

三相AC220V±10%50/60Hz

三相AC380V±10%50/60Hz

控制功率

实际功率由玻璃的面积及玻璃类型确定,依据CB/T 3226-1995标准

输入信号

PT100热电阻信号

输出路数

112路

控制方式

自动/手动

自动控制

≤20时开始加热(可设定)

≥40℃时停止加热(可设定)

超温报警

≥50℃(可设定)

环境温度

-10℃~55℃

安装形式

窗加热控制面板  嵌入式

电源控制箱      壁挂式

防护等级

窗加热控制面板 IP20

电源控制箱IP23

温度设定

SET,然后再按按钮设定所需温度。设定完毕,再按SET键退出。设定温度自动保存。三位八段码平时显示玻璃温度,当需要重新设定温度时,按SET按钮,八段码显示

手动加热

选择手动加热,控制器即开始对玻璃进行加热,面板上ON指示灯亮。当玻璃温度达到设定温度时,自动停止加热,面板上ON指示灯闪烁

自动加热

选择自动加热,控制器根据设定温度对玻璃进行加热。当玻璃达到设定温度时,自动停止。当玻璃温度下降到低于设定温度10度以上时,控制器会再次对玻璃进行加热

超温报警

当玻璃温度超过设定温度2度以上(防止加热器的余温影响)时,控制上的OT指示灯闪烁。蜂鸣器发出间断报警音,按消音按钮。蜂鸣器关闭,OT指示灯常亮。当温度恢复正常时OT指示灯自复位

试灯功能

按下试灯按键,所有指示灯点亮,用来检测状态指示灯是否处于正常状态

调光功能

拨动调光按钮,可以对面板指示灯的亮度进行调节,以确保值班驾驶员再夜间不受其影响轻松读取信息

详细参数请联系客服